FCMGMT-MIB -- Last edit date: Aug 19th, 2001 DEFINITIONS ::= BEGIN IMPORTS IpAddress, TimeTicks, experimental FROM RFC1155-SMI OBJECT-TYPE FROM RFC-1212 DisplayString FROM RFC1213-MIB TRAP-TYPE FROM RFC-1215; ---------------------------------------------------------------------- --Textual conventions for this MIB FcNameId ::= OCTET STRING (SIZE(8)) FcGlobalId ::= OCTET STRING (SIZE(16)) FcAddressId ::= OCTET STRING (SIZE(3)) FcEventSeverity ::= INTEGER { unknown (1), emergency (2), alert (3), critical (4), error (5), warning (6), notify (7), info (8), debug (9), mark (10) -- All messages logged } FcUnitType ::= INTEGER { unknown(1), other(2), -- none of the following hub(3), -- passive connectivity unit -- supporting loop protocol. switch(4), -- active connectivity unit -- supporting multiple protocols. gateway(5), -- unit that converts not only -- the interface but also encapsulates -- the frame into another protocol. The -- assumption is that there is always -- two gateways connected together. For -- example, FC <-> ATM. converter(6), -- unit that converts from one -- interface to another. For -- example, FC <-> SCSI. hba(7), -- host bus adapter proxy-agent(8), -- software proxy-agent storage-device(9), -- disk,cd,tape,etc host(10), -- host computer storage-subsystem(11), -- raid, library, etc module(12), -- subcomponent of a system swdriver(13), -- software driver storage-access-device(14), -- Provides storage management -- and access for hetergeneous -- hosts and heterogeneous devices. wdm(15), -- waveform division mutiplexer ups(16), -- uninterruptable power supply nas(17) -- network attached storage (NFS/CIFS) } ---------------------------------------------------------------------- fcmgmt OBJECT IDENTIFIER ::= { experimental 94 } -- groups in fcmgmt connSet OBJECT IDENTIFIER ::= { fcmgmt 1 } trapReg OBJECT IDENTIFIER ::= { fcmgmt 2 } statSet OBJECT IDENTIFIER ::= { fcmgmt 4 } connUnitServiceSet OBJECT IDENTIFIER ::= { fcmgmt 5 } connUnitServiceScalars OBJECT IDENTIFIER ::= { connUnitServiceSet 1 } connUnitServiceTables OBJECT IDENTIFIER ::= { connUnitServiceSet 2 } revisionNumber OBJECT-TYPE SYNTAX DisplayString (SIZE (4)) ACCESS read-only STATUS mandatory DESCRIPTION "This is the revision number for this MIB. The format of the revision value is as follows (0) = high order major revision number (1) = low order major revision number (2) = high order minor revision number (3) = low order minor revision number The value will be stored as an ASCII value. The following is the current value of this object. (0) = '0' (1) = '4' (2) = '0' (3) = '0' This defines a revision of 04.00 " ::= { fcmgmt 3 } -- the connectivity unit group -- Implementation of the group is mandatory for all systems. uNumber OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "The number of connectivity units present on this system (represented by this agent). May be a count of the boards in a chassis or the number of full boxes in a rack." DEFVAL { 1 } ::= { connSet 1 } systemURL OBJECT-TYPE SYNTAX DisplayString ACCESS read-write STATUS mandatory DESCRIPTION "The top-level URL of the system. If it does not exist the value is empty string. The URL format is implementation dependant and can have keywords embedded that are preceeded by a percent sign (eg, %USER). The following are the defined keywords that will be recognized and replaced with data during a launch. USER - replace with username PASSWORD - replace with password GLOBALID - replace with globalid SERIALNO - replace with serial number A management application will read this object from the MIB, provide values for any of the keywords listed above that are present in the string, and then use the URL to invoke or launch the program referenced. If write is not supported, then return invalid. This value will be retained across boots." DEFVAL { "" } ::= { connSet 2 } statusChangeTime OBJECT-TYPE SYNTAX TimeTicks ACCESS read-only STATUS obsolete DESCRIPTION "The sysuptime timestamp in centiseconds at which the last status change occurred for any members of the set." ::= { connSet 3 } configurationChangeTime OBJECT-TYPE SYNTAX TimeTicks ACCESS read-only STATUS obsolete DESCRIPTION "The sysuptime timestamp in centiseconds at which the last configuration change occurred for any members of the set. This represents a union of change information for connUnitConfigurationChangeTime." ::= { connSet 4 } connUnitTableChangeTime OBJECT-TYPE SYNTAX TimeTicks ACCESS read-only STATUS obsolete DESCRIPTION "The sysuptime timestamp in centiseconds at which the connUnitTable was updated (an entry was either added or deleted." ::= { connSet 5 } -- The Connectivity table contains general information on the -- system's units. connUnitTable OBJECT-TYPE SYNTAX SEQUENCE OF ConnUnitEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "The connectivity table contains general information on the system's units. This is the list of units under a single SNMP agent. The number of entries is given by the value of uNumber. It is 1 for stand-alone system." ::= { connSet 6 } connUnitEntry OBJECT-TYPE SYNTAX ConnUnitEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "A connectivity unit entry containing objects for a particular unit." INDEX { connUnitId } ::= { connUnitTable 1 } ConnUnitEntry ::= SEQUENCE { connUnitId FcGlobalId, connUnitGlobalId FcGlobalId, connUnitType FcUnitType, connUnitNumports INTEGER, connUnitState INTEGER, connUnitStatus INTEGER, connUnitProduct DisplayString, connUnitSn DisplayString, connUnitUpTime TimeTicks, connUnitUrl DisplayString, connUnitDomainId OCTET STRING, connUnitProxyMaster INTEGER, connUnitPrincipal INTEGER, connUnitNumSensors INTEGER, connUnitStatusChangeTime TimeTicks, connUnitConfigurationChangeTime TimeTicks, connUnitNumRevs INTEGER, connUnitNumZones INTEGER, connUnitModuleId FcGlobalId, connUnitName DisplayString, connUnitInfo DisplayString, connUnitControl INTEGER, connUnitContact DisplayString, connUnitLocation DisplayString, connUnitEventFilter FcEventSeverity, connUnitNumEvents INTEGER, connUnitMaxEvents INTEGER, connUnitEventCurrID INTEGER, connUnitFabricID FcGlobalId, connUnitNumLinks INTEGER, connUnitVendorId DisplayString } connUnitId OBJECT-TYPE SYNTAX FcGlobalId ACCESS read-only STATUS mandatory DESCRIPTION "The unique identification for this connectivity unit among those within this proxy domain. The value MUST be unique within the proxy domain because it is the index variable for connUnitTable. The value assigned to a given conectivity unit SHOULD be persistent across agent and unit resets. It SHOULD be the same as connUnitGlobalId if connUnitGlobalId is known and stable." ::= { connUnitEntry 1 } connUnitGlobalId OBJECT-TYPE SYNTAX FcGlobalId ACCESS read-only STATUS mandatory DESCRIPTION "An optional global-scope identifier for this connectivity unit. It MUST be a WWN for this connectivity unit or 16 octets of value zero. WWN formats requiring fewer than 16 octets MUST be extended to 16 octets with trailing zero octets, Left justified, zero filled, If a WWN is used for connUnitId, the same WWN MUST be used for connUnitGlobalId. When a non-zero value is provided, it SHOULD be persistent across agent and unit resets. It SHOULD be globally unique. It SHOULD be one of these FC-PH/PH3 formats: IEEE (NAA=1) IEEE Extended (NAA=2) IEEE Registered (NAA=5). IEEE Registered extended (NAA=6). Use of the IEEE formats allows any IEEE-registered vendor to assure global uniqueness independently. The following are some references on IEEE WWN formats: http://standards.ieee.org/regauth/oui/tutorials/fibreformat.html http://standards.ieee.org/regauth/oui/tutorials/fibrecomp_id.html If one or more WWNs are associated with the connUnit via other management methods, one of them SHOULD be used for connUnitGlobalId. If there is not a WWN assigned specifically to the connUnit, there is some merit, though not a requirement, to using a WWN assigned to (one of) its permanently attached FC/LAN interface(s). This can not risk uniqueness, though. As a counterexample, if your agent runs in a host and the host has an HBA, it is quite possible that agent, host, and HBA will all be distinct connUnits, so the host and agent can not use the WWN of the HBA. Another example: If your hub has a built-in Ethernet port, it might be reasonable for the hub to use its MAC address (prefixed with the appropriate NAA) as its connUnitId. But if the Ethernet were a replaceable PCCard, the hub should have an independent ID." ::= { connUnitEntry 2 } connUnitType OBJECT-TYPE SYNTAX FcUnitType ACCESS read-only STATUS mandatory DESCRIPTION "The type of this connectivity unit." ::= { connUnitEntry 3 } connUnitNumports OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "Number of physical ports in the connectivity unit (internal/embedded, external)." ::= { connUnitEntry 4 } connUnitState OBJECT-TYPE SYNTAX INTEGER { unknown(1), online(2), -- available for meaningful work offline(3) -- unavailable for meaningful work, for -- example in self-test mode, configuration, etc. } ACCESS read-only STATUS mandatory DESCRIPTION "This object reports the overall state of the connectivity unit. The meaning of all values is essentially self-explanatory. Any of these values may occur with any of the ConnUnitStatus values." ::= { connUnitEntry 5 } connUnitStatus OBJECT-TYPE SYNTAX INTEGER { unknown(1), unused(2), -- cannot report status ok(3), -- available for meaningful work warning(4), -- something needs attention failed(5) -- something has failed } ACCESS read-only STATUS mandatory DESCRIPTION "Overall status of the connectivity unit. The goal of this object is to be the single poll point to check the status of the connunit. If there is any other component that has warning, then this should be set to warning, etc. Any of these values may occur with any of the ConnUnitState values." ::= { connUnitEntry 6 } connUnitProduct OBJECT-TYPE SYNTAX DisplayString (SIZE (0..79)) ACCESS read-only STATUS mandatory DESCRIPTION "The connectivity unit vendor's product model name." ::= { connUnitEntry 7 } connUnitSn OBJECT-TYPE SYNTAX DisplayString (SIZE (0..79)) ACCESS read-only STATUS mandatory DESCRIPTION "The serial number for this connectivity unit." ::= { connUnitEntry 8 } connUnitUpTime OBJECT-TYPE SYNTAX TimeTicks ACCESS read-only STATUS mandatory DESCRIPTION "The number of centiseconds since the last unit initialization." ::= { connUnitEntry 9 } connUnitUrl OBJECT-TYPE SYNTAX DisplayString ACCESS read-write STATUS mandatory DESCRIPTION "URL to launch a management application, if applicable. Otherwise empty string. In a standalone unit, this would be the same as the top-level URL. This has the same definition as systemURL for keywords. If write is not supported, then return invalid. This value will be retained across boots." ::= { connUnitEntry 10 } connUnitDomainId OBJECT-TYPE SYNTAX OCTET STRING (SIZE(3)) ACCESS read-only STATUS mandatory DESCRIPTION "24 bit Fibre Channel address ID of this connectivity unit, right justified with leading zero's if required. This should be set to the Fibre Channel address ID or if it is a switch it would be set to the Domain Controller address. If this value is not applicable, return all bits set to 1." ::= { connUnitEntry 11 } connUnitProxyMaster OBJECT-TYPE SYNTAX INTEGER { unknown(1), no(2), yes(3) } ACCESS read-only STATUS mandatory DESCRIPTION "A value of 'yes' means this is the proxy master unit for a set of managed units. For example, this could be the only unit with a management card in it for a set of units. A standalone unit should return 'yes' for this object." ::= { connUnitEntry 12 } connUnitPrincipal OBJECT-TYPE SYNTAX INTEGER { unknown(1), no(2), yes(3) } ACCESS read-only STATUS mandatory DESCRIPTION "Whether this connectivity unit is the principal unit within the group of fabric elements. If this value is not applicable, return unknown." ::= { connUnitEntry 13 } connUnitNumSensors OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "Number of sensors in the connUnitSensorTable." ::= { connUnitEntry 14 } connUnitStatusChangeTime OBJECT-TYPE SYNTAX TimeTicks ACCESS read-only STATUS obsolete DESCRIPTION "The sysuptime timestamp in centiseconds at which the last status change occurred." ::= { connUnitEntry 15 } connUnitConfigurationChangeTime OBJECT-TYPE SYNTAX TimeTicks ACCESS read-only STATUS obsolete DESCRIPTION "The sysuptime timestamp in centiseconds at which the last configuration change occurred." ::= { connUnitEntry 16 } connUnitNumRevs OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "The number of revisions in the connUnitRevsTable." DEFVAL { 1 } ::= { connUnitEntry 17 } connUnitNumZones OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS obsolete DESCRIPTION "Number of zones defined in connUnitZoneTable." ::= { connUnitEntry 18 } connUnitModuleId OBJECT-TYPE SYNTAX FcGlobalId ACCESS read-only STATUS mandatory DESCRIPTION "This is a unique id, persistent between boots, that can be used to group a set of connUnits together into a module. The intended use would be to create a connUnit with a connUnitType of 'module' to represent a physical or logical group of connectivity units. Then the value of the group would be set to the value of connUnitId for this 'container' connUnit. connUnitModuleId should be zeros if this connUnit is not part of a module." ::= { connUnitEntry 19 } connUnitName OBJECT-TYPE SYNTAX DisplayString (SIZE(0..79)) ACCESS read-write STATUS mandatory DESCRIPTION "A display string containing a name for this connectivity unit. This object value should be persistent between boots." ::= { connUnitEntry 20 } connUnitInfo OBJECT-TYPE SYNTAX DisplayString ACCESS read-write STATUS mandatory DESCRIPTION "A display string containing information about this connectivity unit. This object value should be persistent between boots." ::= { connUnitEntry 21 } connUnitControl OBJECT-TYPE SYNTAX INTEGER { unknown(1), invalid(2), resetConnUnitColdStart(3), resetConnUnitWarmStart(4), offlineConnUnit(5), onlineConnUnit(6) } ACCESS read-write STATUS mandatory DESCRIPTION "This object is used to control the addressed connUnit. NOTE: 'Cold Start' and 'Warm Start' are as defined in MIB II and are not meant to be a factory reset. resetConnUnitColdStart: the addressed unit performs a 'Cold Start' reset. resetConnUnitWarmStart: the addressed unit performs a 'Warm Start' reset. offlineConnUnit: the addressed unit puts itself into an implementation dependant 'offline' state. In general,if a unit is in an offline state, it cannot be used to perform meaningful Fibre Channel work. onlineConnUnit: the addressed unit puts itself into an implementation dependant 'online' state. In general, if a unit is in an online state, it is capable of performing meaningful Fibre Channel work. NOTE: Each implementation may chose not to allow any or all of these values on a SET. " ::= { connUnitEntry 22 } connUnitContact OBJECT-TYPE SYNTAX DisplayString (SIZE (0..79)) ACCESS read-write STATUS mandatory DESCRIPTION "Contact information for this connectivity unit. Persistent across boots." ::= { connUnitEntry 23 } connUnitLocation OBJECT-TYPE SYNTAX DisplayString (SIZE (0..79)) ACCESS read-write STATUS mandatory DESCRIPTION "Location information for this connectivity unit.Persistent across boots." ::= { connUnitEntry 24 } connUnitEventFilter OBJECT-TYPE SYNTAX FcEventSeverity ACCESS read-write STATUS mandatory DESCRIPTION "This value defines the event severity that will be logged by this connectivity unit. All events of severity less than or equal to connUnitEventFilter are logged in connUnitEventTable. Persistent across boots." ::= { connUnitEntry 25 } connUnitNumEvents OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "Number of events currently in the connUnitEventTable." ::= { connUnitEntry 26 } connUnitMaxEvents OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "Max number of events that can be defined in connUnitEventTable." ::= { connUnitEntry 27 } connUnitEventCurrID OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "The last used event id (connUnitEventIndex)." ::= { connUnitEntry 28 } connUnitFabricID OBJECT-TYPE SYNTAX FcGlobalId ACCESS read-only STATUS mandatory DESCRIPTION "A globally unique value to identify the fabric that this ConnUnit belongs to, otherwise empty string. This would typically be equal to the connUnitGlobalID of the primary switch in a Fibre Channel fabric." ::= { connUnitEntry 29 } connUnitNumLinks OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "The number of links in the link table." ::= { connUnitEntry 30 } connUnitVendorId OBJECT-TYPE SYNTAX DisplayString (SIZE (0..79)) ACCESS read-only STATUS mandatory DESCRIPTION "The connectivity unit vendor's name." ::= { connUnitEntry 31 } ------------------------------------------------------------------ -- The Table of revisions for hardware and software elements. connUnitRevsTable OBJECT-TYPE SYNTAX SEQUENCE OF ConnUnitRevsEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "Table of the revisions supported by connectivity units managed by this agent." ::= { connSet 7 } connUnitRevsEntry OBJECT-TYPE SYNTAX ConnUnitRevsEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "" INDEX { connUnitRevsUnitId, connUnitRevsIndex } ::= { connUnitRevsTable 1 } ConnUnitRevsEntry ::= SEQUENCE { connUnitRevsUnitId FcGlobalId, connUnitRevsIndex INTEGER, connUnitRevsRevId DisplayString, connUnitRevsDescription DisplayString } connUnitRevsUnitId OBJECT-TYPE SYNTAX FcGlobalId ACCESS read-only STATUS mandatory DESCRIPTION "The connUnitId of the connectivity unit that contains this revision table." ::= { connUnitRevsEntry 1 } connUnitRevsIndex OBJECT-TYPE SYNTAX INTEGER (1..2147483647) ACCESS read-only STATUS mandatory DESCRIPTION "A unique value among all connUnitRevsEntrys with the same value of connUnitRevsUnitId, in the range between 1 and connUnitNumRevs[connUnitRevsUnitId]." ::= { connUnitRevsEntry 2 } connUnitRevsRevId OBJECT-TYPE SYNTAX DisplayString ACCESS read-only STATUS mandatory DESCRIPTION "A vendor-specific string identifying a revision of a component of the connUnit indexed by connUnitRevsUnitId." ::= { connUnitRevsEntry 3 } connUnitRevsDescription OBJECT-TYPE SYNTAX DisplayString ACCESS read-only STATUS mandatory DESCRIPTION "Description of a component to which the revision corresponds." ::= { connUnitRevsEntry 4 } ----------------------------------------------------------------------- -- The Sensor table connUnitSensorTable OBJECT-TYPE SYNTAX SEQUENCE OF ConnUnitSensorEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "Table of the sensors supported by each connectivity unit managed by this agent." ::= { connSet 8 } connUnitSensorEntry OBJECT-TYPE SYNTAX ConnUnitSensorEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "Each entry contains the information for a specific sensor." INDEX { connUnitSensorUnitId, connUnitSensorIndex } ::= { connUnitSensorTable 1 } ConnUnitSensorEntry ::= SEQUENCE { connUnitSensorUnitId FcGlobalId, connUnitSensorIndex INTEGER (1..2147483647), connUnitSensorName DisplayString, connUnitSensorStatus INTEGER, connUnitSensorInfo DisplayString, connUnitSensorMessage DisplayString, connUnitSensorType INTEGER, connUnitSensorCharacteristic INTEGER } connUnitSensorUnitId OBJECT-TYPE SYNTAX FcGlobalId ACCESS read-only STATUS mandatory DESCRIPTION "The connUnitId of the connectivity unit that contains this sensor table." ::= { connUnitSensorEntry 1 } connUnitSensorIndex OBJECT-TYPE SYNTAX INTEGER (1..2147483647) ACCESS read-only STATUS mandatory DESCRIPTION "A unique value among all connUnitSensorEntrys with the same value of connUnitSensorUnitId, in the range between 1 and connUnitNumSensor[connUnitSensorUnitId]." ::= { connUnitSensorEntry 2} connUnitSensorName OBJECT-TYPE SYNTAX DisplayString ACCESS read-only STATUS mandatory DESCRIPTION "A textual identification of the sensor intended primarily for operator use." ::= { connUnitSensorEntry 3 } connUnitSensorStatus OBJECT-TYPE SYNTAX INTEGER { unknown(1), other(2), -- the sensor indicates other than ok, -- warning or failure. ok(3), -- the sensor indicates ok warning(4), -- the sensor indicates a warning failed(5) -- the sensor indicates failure } ACCESS read-only STATUS mandatory DESCRIPTION "The status indicated by the sensor." ::= { connUnitSensorEntry 4 } connUnitSensorInfo OBJECT-TYPE SYNTAX DisplayString ACCESS read-only STATUS mandatory DESCRIPTION "Miscellaneous static info about the sensor such as its serial number." ::= { connUnitSensorEntry 5 } connUnitSensorMessage OBJECT-TYPE SYNTAX DisplayString ACCESS read-only STATUS mandatory DESCRIPTION "This describes the status of the sensor as a message. It may also provide more resolution on the sensor indication, for example 'Cover temperature 1503K, above nominal operating range'" ::= { connUnitSensorEntry 6 } connUnitSensorType OBJECT-TYPE SYNTAX INTEGER { unknown(1), other(2), battery(3), fan(4), power-supply(5), transmitter(6), enclosure(7), board(8), receiver(9) } ACCESS read-only STATUS mandatory DESCRIPTION "The type of component being monitored by this sensor." ::= { connUnitSensorEntry 7 } connUnitSensorCharacteristic OBJECT-TYPE SYNTAX INTEGER { unknown(1), other(2), temperature(3), pressure(4), emf(5), currentValue(6), -- current is a keyword airflow(7), frequency(8), power(9), door(10) } ACCESS read-only STATUS mandatory DESCRIPTION "The characteristics being monitored by this sensor." ::= { connUnitSensorEntry 8 } ----------------------------------------------------------------------- -- The port table connUnitPortTable OBJECT-TYPE SYNTAX SEQUENCE OF ConnUnitPortEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "Generic information on ports for a specific connUnit." ::= { connSet 10 } connUnitPortEntry OBJECT-TYPE SYNTAX ConnUnitPortEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "Each entry contains the information for a specific port." INDEX { connUnitPortUnitId, connUnitPortIndex } ::= { connUnitPortTable 1 } ConnUnitPortEntry ::= SEQUENCE { connUnitPortUnitId FcGlobalId, connUnitPortIndex INTEGER, connUnitPortType INTEGER, connUnitPortFCClassCap OCTET STRING, connUnitPortFCClassOp OCTET STRING, connUnitPortState INTEGER, connUnitPortStatus INTEGER, connUnitPortTransmitterType INTEGER, connUnitPortModuleType INTEGER, connUnitPortWwn FcGlobalId, connUnitPortFCId FcAddressId, connUnitPortSn DisplayString, connUnitPortRevision DisplayString, connUnitPortVendor DisplayString, connUnitPortSpeed INTEGER, connUnitPortControl INTEGER, connUnitPortName DisplayString, connUnitPortPhysicalNumber INTEGER, connUnitPortStatObject OBJECT IDENTIFIER, connUnitPortProtocolCap OCTET STRING, connUnitPortProtocolOp OCTET STRING, connUnitPortNodeWwn FcNameId, connUnitPortHWState INTEGER } connUnitPortUnitId OBJECT-TYPE SYNTAX FcGlobalId ACCESS read-only STATUS mandatory DESCRIPTION "The connUnitId of the connectivity unit that contains this port." ::= { connUnitPortEntry 1 } connUnitPortIndex OBJECT-TYPE SYNTAX INTEGER (1..2147483647) ACCESS read-only STATUS mandatory DESCRIPTION "A unique value among all connUnitPortEntrys on this connectivity unit, between 1 and connUnitNumPort[connUnitPortUnitId]." ::= { connUnitPortEntry 2 } connUnitPortType OBJECT-TYPE SYNTAX INTEGER { unknown (1), other (2), not-present (3), hub-port (4), n-port (5), -- end port for fabric nl-port (6), -- end port for loop fl-port (7), -- public loop f-port (8), -- fabric port e-port (9), -- fabric expansion port g-port (10), -- generic fabric port domain-ctl (11), -- domain controller hub-controller(12), scsi (13), -- parallel SCSI port escon (14), lan (15), wan (16), ac (17), -- AC power line dc (18), -- DC power line ssa (19), -- serial storage architecture wdm (20), -- optical wave division multiplex ib (21), -- Infiniband ipstore (22) -- IP storage } ACCESS read-only STATUS mandatory DESCRIPTION "The port type." ::= { connUnitPortEntry 3 } connUnitPortFCClassCap OBJECT-TYPE SYNTAX OCTET STRING (SIZE (2)) ACCESS read-only STATUS mandatory DESCRIPTION "Bit mask that specifies the classes of service capability of this port. If this is not applicable, return all bits set to zero. The bits have the following definition: unknown - 0 class-f - 1 class-one - 2 class-two - 4 class-three - 8 class-four - 16 class-five - 32 class-six - 64" ::= { connUnitPortEntry 4 } connUnitPortFCClassOp OBJECT-TYPE SYNTAX OCTET STRING (SIZE (2)) ACCESS read-only STATUS mandatory DESCRIPTION "Bit mask that specifies the classes of service that are currently operational. If this is not applicable, return all bits set to zero. This object has the same definition as connUnitPortFCClassCap" ::= { connUnitPortEntry 5 } connUnitPortState OBJECT-TYPE SYNTAX INTEGER { unknown(1), online(2), -- available for meaningful work offline(3), -- not available for meaningful work bypassed(4), -- no longer used (4/12/00) diagnostics(5) } ACCESS read-only STATUS mandatory DESCRIPTION "The user selected state of the port hardware." ::= { connUnitPortEntry 6 } connUnitPortStatus OBJECT-TYPE SYNTAX INTEGER { unknown (1), unused (2), -- device cannot report this status ready (3), -- FCAL Loop or FCPH Link reset protocol -- initialization has completed warning (4), -- do not use (4/12/00) failure (5), -- do not use (4/12/00) notparticipating (6), -- loop notparticipating and does not -- have a loop address initializing (7), -- protocol is proceeding bypass (8), -- do not use (4/12/00) ols (9), -- FCP offline status other (10) -- status not described above } ACCESS read-only STATUS mandatory DESCRIPTION "An overall protocol status for the port. This value of connUnitPortState is not online, then this is reported Unknown." ::= { connUnitPortEntry 7 } connUnitPortTransmitterType OBJECT-TYPE SYNTAX INTEGER { unknown(1), other(2), unused(3), shortwave(4), longwave(5), copper(6), scsi(7), longwaveNoOFC(8), shortwaveNoOFC(9), longwaveLED(10), ssa(11) } ACCESS read-only STATUS mandatory DESCRIPTION "The technology of the port transceiver." ::= { connUnitPortEntry 8 } connUnitPortModuleType OBJECT-TYPE SYNTAX INTEGER { unknown(1), other(2), gbic(3), embedded(4), -- fixed, ie, oneXnine glm(5), gbicSerialId(6), gbicNoSerialId(7), gbicNotInstalled(8), smallFormFactor(9) -- this is generically a small form factor -- connector. } ACCESS read-only STATUS mandatory DESCRIPTION "The module type of the port connector." ::= { connUnitPortEntry 9 } connUnitPortWwn OBJECT-TYPE SYNTAX FcGlobalId ACCESS read-only STATUS mandatory DESCRIPTION "The World Wide Name of the port if applicable, otherwise all zeros." ::= { connUnitPortEntry 10 } connUnitPortFCId OBJECT-TYPE SYNTAX FcAddressId ACCESS read-only STATUS mandatory DESCRIPTION "This is the assigned Fibre Channel ID of this port. This value is expected to be a Big Endian value of 24 bits. If this is loop, then it is the ALPA that is connected. If this is an eport, then it will only contain the domain ID left justified, zero filled. If this port does not have a Fibre Channel address, return all bits set to 1." ::= { connUnitPortEntry 11 } connUnitPortSn OBJECT-TYPE SYNTAX DisplayString (SIZE(0..79)) ACCESS read-only STATUS mandatory DESCRIPTION "The serial number of the unit (e.g., for a GBIC). If this is not applicable, return empty string." ::= { connUnitPortEntry 12 } connUnitPortRevision OBJECT-TYPE SYNTAX DisplayString (SIZE(0..79)) ACCESS read-only STATUS mandatory DESCRIPTION "The port revision (e.g., for a GBIC)." ::= { connUnitPortEntry 13 } connUnitPortVendor OBJECT-TYPE SYNTAX DisplayString (SIZE(0..79)) ACCESS read-only STATUS mandatory DESCRIPTION "The port vendor (e.g., for a GBIC)." ::= { connUnitPortEntry 14 } connUnitPortSpeed OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "The speed of the port in kilobytes per second." ::= { connUnitPortEntry 15 } connUnitPortControl OBJECT-TYPE SYNTAX INTEGER { unknown(1), invalid(2), resetConnUnitPort(3), bypassConnUnitPort(4), unbypassConnUnitPort(5), offlineConnUnitPort(6), onlineConnUnitPort(7), resetConnUnitPortCounters(8) } ACCESS read-write STATUS mandatory DESCRIPTION "This object is used to control the addressed connUnit's port. Valid commands are: resetConnUnitPort: If the addressed connUnit allows this operation to be performed to this port, the addressed port performs a vendor-specific 'reset' operation. Examples of these operations are: the Link Reset protocol, the Loop Initialization protocol, or a resynchronization occurring between the transceiver in the addressed port to the transceiver that the port is connected to. bypassConnUnitPort: If the addressed connUnit allows this operation to be performed to this port, the addressed port performs a vendor-specific 'bypass' operation. Examples of these operations are: transitioning from online to offline, a request(NON-PARTICIPATING) command to the Loop Port state machine, or removal of the port from an arbitrated loop by a hub. unbypassConnUnitPort: If the addressed connUnit allows this operation to be performed to this port, the addressed port performs a vendor-specific 'unbypass' operation. Examples of these operations are: the Link Failure protocol, a request(PARTICIPATING) command to the Loop Port state machine, or addition of the port to an arbitrated loop by a hub. offlineConnUnitPort: If the addressed connUnit allows this operation to be performed to this port, the addressed port performs a vendor-specific 'offline' operation. Examples of these operations are: disabling a port's transceiver, the Link Failure protocol, request(NON-PARTICIPATING) command to the Loop Port state machine, or removal of the port from an arbitrated loop by a hub. onlineConnUnitPort: If the addressed connUnit allows this operation to be performed to this port, the addressed port performs a vendor-specific 'online' operation. Examples of these operations are: enabling a port's transceiver, the Link Failure protocol, request(PARTICIPATING) command to the Loop Port state machine, or addition of the port from an arbitrated loop by a hub. resetConnUnitPortCounters: If the addressed connUnit allows this operation to be performed to this port, the addressed port statistics table counters will be set to zero. NOTE: Each implementation may chose not to allow any or all of these values on a SET. On a read, if you do not support write, then return invalid. Otherwise return the last control operation attempted." ::= { connUnitPortEntry 16 } connUnitPortName OBJECT-TYPE SYNTAX DisplayString ACCESS read-write STATUS mandatory DESCRIPTION "A user-defined name for this port. This means that up to DisplayString characters may be supported. If less than, then the name will be truncated in the connunit." ::= { connUnitPortEntry 17 } connUnitPortPhysicalNumber OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "This is the internal port number this port is known by. In many implementations, this should be the same as connUnitPortIndex. Some implementations may have an internal port representation not compatible with the rules for table indeces. In that case, provide the internal representation of this port in this object. This value may also be used in the connUnitLinkPortNumberX or connUnitLinkPortNumberY objects of the connUnitLinkTable." ::= { connUnitPortEntry 18 } connUnitPortStatObject OBJECT-TYPE SYNTAX OBJECT IDENTIFIER ACCESS read-only STATUS deprecated DESCRIPTION "This contains the OID of the first object of the table that contains the statistics for this particular port. If this has a value of zero, then there are no statistics available for this port. The port type information will help identify the statistics objects that will be found in the table." ::= { connUnitPortEntry 19 } connUnitPortProtocolCap OBJECT-TYPE SYNTAX OCTET STRING (SIZE (2)) ACCESS read-only STATUS mandatory DESCRIPTION "Bit mask that specifies the driver level protocol capability of this port. If this is not applicable, return all bits set to zero. The bits have the following definition: unknown - 0 Loop - 1 Fabric - 2 SCSI - 4 TCP/IP - 8 VI - 16 FICON - 32" ::= { connUnitPortEntry 20 } connUnitPortProtocolOp OBJECT-TYPE SYNTAX OCTET STRING (SIZE (2)) ACCESS read-only STATUS mandatory DESCRIPTION "Bit mask that specifies the driver level protocol(s) that are currently operational. If this is not applicable, return all bits set to zero. This object has the same definition as connUnitPortProtocolCap" ::= { connUnitPortEntry 21 } connUnitPortNodeWwn OBJECT-TYPE SYNTAX FcNameId ACCESS read-only STATUS mandatory DESCRIPTION "The Node World Wide Name of the port if applicable, otherwise all zeros. This should have the same value for a group of related ports. The container is defined as the largest physical unit. For example, all ports on HBAs on a host will have the same Node WWN. All ports on the same storage subsystem will have the same Node WWN." ::= { connUnitPortEntry 22 } connUnitPortHWState OBJECT-TYPE SYNTAX INTEGER { unknown (1), failed (2), -- port failed diagnostics bypassed (3), -- FCAL bypass, loop only active (4), -- connected to a device loopback (5), -- Port in ext loopback txfault (6), -- Transmitter fault noMedia (7), -- media not installed linkDown (8) -- waiting for activity (rx sync) } ACCESS read-only STATUS mandatory DESCRIPTION "The hardware detected state of the port." ::= { connUnitPortEntry 23 } ----------------------------------------------------------------------- -- event group connUnitEventTable OBJECT-TYPE SYNTAX SEQUENCE OF ConnUnitEventEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "The table of connectivity unit events. Errors, warnings, and information should be reported in this table." ::= { connSet 11 } connUnitEventEntry OBJECT-TYPE SYNTAX ConnUnitEventEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "Each entry contains information on a specific event for the given connectivity unit." INDEX { connUnitEventUnitId, connUnitEventIndex } ::= { connUnitEventTable 1 } ConnUnitEventEntry ::= SEQUENCE { connUnitEventUnitId FcGlobalId, connUnitEventIndex INTEGER (1..2147483647), connUnitEventId INTEGER, connUnitREventTime DisplayString, connUnitSEventTime TimeTicks, connUnitEventSeverity FcEventSeverity, connUnitEventType INTEGER, connUnitEventObject OBJECT IDENTIFIER, connUnitEventDescr DisplayString } connUnitEventUnitId OBJECT-TYPE SYNTAX FcGlobalId ACCESS read-only STATUS mandatory DESCRIPTION "The connUnitId of the connectivity unit that contains this event table." ::= { connUnitEventEntry 1 } connUnitEventIndex OBJECT-TYPE SYNTAX INTEGER (1..2147483647) ACCESS read-only STATUS mandatory DESCRIPTION "Each connectivity unit has its own event buffer. As it wraps, it may write over previous events. This object is an index into the buffer. It is recommended that this table be read using 'getNext's to retrieve the initial table. The management application should read the event table at periodic intervals and then determine if any new entries were added by comparing the last known index value with the current highest index value. The management application should then update its copy of the event table. If the read interval is too long, it is possible that there may be events that may not be contained in the agent's internal event buffer. For example, an agent may read events 50-75. At the next read interval, connUnitEventCurrID is 189. If the management app tries to read event index 76, and the agent's internal buffer is 100 entries max, event index 76 will no longer be available. The index value is an incrementing integer starting from one every time there is a table reset. On table reset, all contents are emptied and all indeces are set to zero. When an event is added to the table, the event is assigned the next higher integer value than the last item entered into the table. If the index value reaches its maximum value, the next item entered will cause the index value to roll over and start at one again." ::= { connUnitEventEntry 2 } connUnitEventId OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS deprecated DESCRIPTION "The internal event Id. Incremented for each event, ranging between 1 and connUnitMaxEvents. Not used as table index to simplify the agent implementation. When this reaches the end of the range specified by connUnitMaxEvents, the Id will roll over to start at one. This value will be set back to one at reset. The relationship of this value to the index is that internal event id may represent a smaller number than a 32 bit integer (eg max 100 entries) and would only have a value range up to connUnitMaxEvents." ::= { connUnitEventEntry 3 } connUnitREventTime OBJECT-TYPE SYNTAX DisplayString (SIZE (0..15)) ACCESS read-only STATUS mandatory DESCRIPTION "This is the real time when the event occurred. It has the following format. DDMMYYYY HHMMSS DD=day number MM=month number YYYY=year number HH=hour number MM=minute number SS=seconds number If not applicable, return either a NULL string or '00000000 000000'." ::= { connUnitEventEntry 4 } connUnitSEventTime OBJECT-TYPE SYNTAX TimeTicks ACCESS read-only STATUS mandatory DESCRIPTION "This is the sysuptime timestamp when the event occurred." ::= { connUnitEventEntry 5 } connUnitEventSeverity OBJECT-TYPE SYNTAX FcEventSeverity ACCESS read-only STATUS mandatory DESCRIPTION "The event severity level." ::= { connUnitEventEntry 6 } connUnitEventType OBJECT-TYPE SYNTAX INTEGER { unknown(1), other(2), status(3), configuration(4), topology(5) } ACCESS read-only STATUS mandatory DESCRIPTION "The type of this event." ::= { connUnitEventEntry 7 } connUnitEventObject OBJECT-TYPE SYNTAX OBJECT IDENTIFIER ACCESS read-only STATUS mandatory DESCRIPTION "This is used with the connUnitEventType to identify which object the event refers to. Examples are connUnitPortStatus.connUnitId.connUnitPortIndex, connUnitStatus.connUnitId, etc." ::= { connUnitEventEntry 8 } connUnitEventDescr OBJECT-TYPE SYNTAX DisplayString ACCESS read-only STATUS mandatory DESCRIPTION "The description of the event." ::= { connUnitEventEntry 9 } ------------------------------------------------------------------ -- The link table -- is intended to organize and communicate -- any information the agent possesses -- which would assist a management application -- to discover the CONNECTIVITY UNITS in the -- framework and the TOPOLOGY of their interconnect. -- That is, the goal is to assist the management -- application not only to LIST the elements of the framework, -- but to MAP them. -- With this goal, the agent SHOULD include -- as much as it possesses about any links -- from its own connectivity units to others, -- including links among its own units. -- An agent SHOULD include partial information -- about links if it is not able to fully -- define them. -- For an entry to be considered to be valid, both the X (local) -- and the Y (remote) need to have one valid value. -- If the agent is able to discover links -- which do not directly attach to members of its agency -- and its discovery algorithm gives some assurance -- the links are recently valid, it MAY include these links. -- Link information entered by administrative action -- MAY be included even if not validated directly -- if the link has at least one endpoint in this agency, -- but SHOULD NOT be included otherwise. -- A connectivity unit should fill the table in as best it can. -- One of the methods to fill this in would be to use the RNID -- ELS (reference ANSI T11.3 draft standard FC-FS). This -- allows one to query a port for the information needed for -- the link table. -- This table is accessed either directly if the management -- software has an index value or via GetNexts. The value of -- the indexes are not required to be contiguous. Each entry -- created in this table will be assigned an index. This -- relationship is kept persistent until the entry is removed -- from the table or the system is reset. The total number of -- entries are defined by the size of the table connUnitLinkTable OBJECT-TYPE SYNTAX SEQUENCE OF ConnUnitLinkEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "A list of links know to this agent from this connectivity unit to other connectivity units." ::= { connSet 12 } connUnitLinkEntry OBJECT-TYPE SYNTAX ConnUnitLinkEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "An entry describing a particular link to another." INDEX { connUnitLinkUnitId, connUnitLinkIndex } ::= { connUnitLinkTable 1 } ConnUnitLinkEntry ::= SEQUENCE { connUnitLinkUnitId FcGlobalId, connUnitLinkIndex INTEGER, connUnitLinkNodeIdX OCTET STRING, connUnitLinkPortNumberX INTEGER, connUnitLinkPortWwnX FcGlobalId, connUnitLinkNodeIdY OCTET STRING, connUnitLinkPortNumberY INTEGER, connUnitLinkPortWwnY FcGlobalId, connUnitLinkAgentAddressY OCTET STRING, connUnitLinkAgentAddressTypeY INTEGER, connUnitLinkAgentPortY INTEGER, connUnitLinkUnitTypeY FcUnitType, connUnitLinkConnIdY OCTET STRING, connUnitLinkCurrIndex INTEGER } connUnitLinkUnitId OBJECT-TYPE SYNTAX FcGlobalId ACCESS read-only STATUS mandatory DESCRIPTION "The connUnitId of the connectivity unit that contains this link table." ::= { connUnitLinkEntry 1 } connUnitLinkIndex OBJECT-TYPE SYNTAX INTEGER (1..2147483647) ACCESS read-only STATUS mandatory DESCRIPTION "This index is used to create a unique value for each entry in the link table with the same connUnitLinkUnitId. The value can only be reused if it is not currently in use and the value is the next candidate to be used. This value wraps at the highest value represented by the size of INTEGER. This value is reset to zero when the system is reset and the first value to be used is one." ::= { connUnitLinkEntry 2 } connUnitLinkNodeIdX OBJECT-TYPE SYNTAX OCTET STRING (SIZE(16)) ACCESS read-only STATUS mandatory DESCRIPTION "The node WWN of the unit at one end of the link. If the node WWN is unknown and the node is a connUnit in the responding agent then the value of this object MUST BE equal to its connUnitID." ::= { connUnitLinkEntry 3 } connUnitLinkPortNumberX OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "The port number on the unit specified by connUnitLinkNodeIdX if known, otherwise -1. If the value is nonnegative then it will be equal to connUnitPortPhysicalNumber." ::= { connUnitLinkEntry 4 } connUnitLinkPortWwnX OBJECT-TYPE SYNTAX FcGlobalId ACCESS read-only STATUS mandatory DESCRIPTION "The port WWN of the unit specified by connUnitLinkNodeIdX if known, otherwise 16 octets of binary 0" ::= { connUnitLinkEntry 5 } connUnitLinkNodeIdY OBJECT-TYPE SYNTAX OCTET STRING (SIZE(16)) ACCESS read-only STATUS mandatory DESCRIPTION "The node WWN of the unit at the other end of the link. If the node WWN is unknown and the node is a connUnit in the responding SNMP agency then the value of this object MUST BE equal to its connUnitID." ::= { connUnitLinkEntry 6 } connUnitLinkPortNumberY OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "The port number on the unit specified by connUnitLinkNodeIdY if known, otherwise -1. If the value is nonnegative then it will be equal to connUnitPortPhysicalNumber." ::= { connUnitLinkEntry 7 } connUnitLinkPortWwnY OBJECT-TYPE SYNTAX FcGlobalId ACCESS read-only STATUS mandatory DESCRIPTION "The port WWN on the unit specified by connUnitLinkNodeIdY if known, otherwise 16 octets of binary 0" ::= { connUnitLinkEntry 8 } connUnitLinkAgentAddressY OBJECT-TYPE SYNTAX OCTET STRING (SIZE(16)) ACCESS read-only STATUS mandatory DESCRIPTION "The address of an FCMGMT MIB agent for the node identified by connUnitLinkNodeIdY, if known; otherwise 16 octets of binary 0" ::= { connUnitLinkEntry 9 } connUnitLinkAgentAddressTypeY OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "If connUnitLinkAgentAddressY is nonzero, it is a protocol address. ConnUnitLinkAgentAddressTypeY is the the 'address family number' assigned by IANA to identify the address format. (eg, 1 is Ipv4, 2 is Ipv6). If connUnitLinkAgentAddressY is all zeros, then this value is ignored." ::= { connUnitLinkEntry 10 } connUnitLinkAgentPortY OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "The IP port number for the agent. This is provided in case the agent is at a non-standard SNMP port." ::= { connUnitLinkEntry 11 } connUnitLinkUnitTypeY OBJECT-TYPE SYNTAX FcUnitType ACCESS read-only STATUS mandatory DESCRIPTION "Type of the FC connectivity unit as defined in connUnitType." ::= { connUnitLinkEntry 12 } connUnitLinkConnIdY OBJECT-TYPE SYNTAX OCTET STRING (SIZE(3)) ACCESS read-only STATUS mandatory DESCRIPTION "This is the Fibre Channel ID of this port. If the connectivity unit is a switch, this is expected to be a Big Endian value of 24 bits. If this is loop, then it is the ALPA that is connected. If this is an eport, then it will only contain the domain ID. If not any of those, unknown or cascaded loop, return all bits set to 1." ::= { connUnitLinkEntry 13 } connUnitLinkCurrIndex OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "The last used link index." ::= { connUnitLinkEntry 14 } -- The Active Zone table is defined by -- read-only view of the active zone configuration. -- Based on the fabric zone server defined in the FC-GS-3 standard and -- the enhanced zone server proposed for FC-GS-4. -- Allows alias zone members (GS-4 feature) and includes an alias -- table. -- Zone table and Alias table are flat, double-indexed MIB tables. -- Database view of inactive zone sets is not provided. (Note: This -- could be added by adding a third index (connUnitZoneSetIndex) -- and an zone set active flag to the connUnitActiveZonesTable -- table.) -- Undefined, vendor-specific bytes have not been included for the bit -- mask objects connUnitZoneCapabilities and -- connUnitZoneEnforcementState. connUnitZoneTable OBJECT-TYPE SYNTAX SEQUENCE OF ConnUnitZoneEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "" ::= { connSet 13 } connUnitZoneEntry OBJECT-TYPE SYNTAX ConnUnitZoneEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "" INDEX { connUnitZoneIndex, connUnitZoneMemberIndex } ::= { connUnitZoneTable 1 } ConnUnitZoneEntry ::= SEQUENCE { connUnitZoneIndex INTEGER, connUnitZoneMemberIndex INTEGER, connUnitZoneSetName DisplayString, connUnitZoneSetNumZones INTEGER, connUnitZoneName DisplayString, connUnitZoneCapabilities OCTET STRING, connUnitZoneEnforcementState OCTET STRING, connUnitZoneAttributeBlock OCTET STRING, connUnitZoneNumMembers INTEGER, connUnitZoneMemberIdType INTEGER, connUnitZoneMemberID FcGlobalId } connUnitZoneIndex OBJECT-TYPE SYNTAX INTEGER (1..2147483647) ACCESS read-only STATUS mandatory DESCRIPTION "Unique table index for each zone. Valid values are between 1 and connUnitZoneSetNumZones." ::= { connUnitZoneEntry 1 } connUnitZoneMemberIndex OBJECT-TYPE SYNTAX INTEGER (1..2147483647) ACCESS read-only STATUS mandatory DESCRIPTION "Unique table index for each zone member. Valid values are between 1 and connUnitZoneNumMembers." ::= { connUnitZoneEntry 2 } connUnitZoneSetName OBJECT-TYPE SYNTAX DisplayString (SIZE (0..79)) ACCESS read-only STATUS mandatory DESCRIPTION "Name of the active zone set to which the zone and zone member belong." ::= { connUnitZoneEntry 3 } connUnitZoneSetNumZones OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "The number of zones in the active zone set." ::= { connUnitZoneEntry 4 } connUnitZoneName OBJECT-TYPE SYNTAX DisplayString (SIZE (0..79)) ACCESS read-only STATUS mandatory DESCRIPTION "Name of the zone." ::= { connUnitZoneEntry 5 } connUnitZoneCapabilities OBJECT-TYPE SYNTAX OCTET STRING (SIZE(1)) ACCESS read-only STATUS mandatory DESCRIPTION "1-byte bit mask that specifies the zoning capabilities supported by the fabric. Bit 7 - Soft zones supported. Bit 6 - Hard zones supported. Bits 5-0 - Reserved." ::= { connUnitZoneEntry 6 } connUnitZoneEnforcementState OBJECT-TYPE SYNTAX OCTET STRING (SIZE(1)) ACCESS read-only STATUS mandatory DESCRIPTION "1-byte bit mask that specifies the current enforcement of the Zone Set. Bit 7 - Soft zone set enforced. Bit 6 - Hard zone set enforced. Bits 5-0 - Reserved." ::= { connUnitZoneEntry 7 } connUnitZoneAttributeBlock OBJECT-TYPE SYNTAX OCTET STRING (SIZE(80)) ACCESS read-only STATUS mandatory DESCRIPTION "A variable length structure that contains extended zone attributes defined in the FC-GS-4 enhanced zone server. See FC-GS-4 draft standard for details and format of the structure. Support of this object is optional." ::= { connUnitZoneEntry 8 } connUnitZoneNumMembers OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "Number of zone members in the zone: connUnitZoneName." ::= { connUnitZoneEntry 9 } connUnitZoneMemberIdType OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "Type of zone member ID: 1- Port WWN 2- Domain & Port ID 3- FC Address 4- Node WWN 5- Alias Name 6-'FF'h - Vendor specified." ::= { connUnitZoneEntry 10 } connUnitZoneMemberID OBJECT-TYPE SYNTAX FcGlobalId ACCESS read-only STATUS mandatory DESCRIPTION "ID of the zone member based on connUnitZoneMemberIdType." ::= { connUnitZoneEntry 11 } -- Zone Alias Table connUnitZoningAliasTable OBJECT-TYPE SYNTAX SEQUENCE OF ConnUnitZoningAliasEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "" ::= { connSet 14 } connUnitZoningAliasEntry OBJECT-TYPE SYNTAX ConnUnitZoningAliasEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "" INDEX { connUnitZoningAliasIndex, connUnitZoningAliasMemberIndex } ::= { connUnitZoningAliasTable 1 } ConnUnitZoningAliasEntry ::= SEQUENCE { connUnitZoningAliasIndex INTEGER, connUnitZoningAliasMemberIndex INTEGER, connUnitZoningAliasNumAliases INTEGER, connUnitZoningAliasName DisplayString, connUnitZoningAliasNumMembers INTEGER, connUnitZoningAliasMemberIdType INTEGER, connUnitZoningAliasMemberID FcGlobalId } connUnitZoningAliasIndex OBJECT-TYPE SYNTAX INTEGER (1..2147483647) ACCESS read-only STATUS mandatory DESCRIPTION "Unique table index for each alias. Valid values are between 1 and connUnitZoningAliasNumAliases." ::= { connUnitZoningAliasEntry 1 } connUnitZoningAliasMemberIndex OBJECT-TYPE SYNTAX INTEGER (1..2147483647) ACCESS read-only STATUS mandatory DESCRIPTION "Unique table index for each alias member. Valid values are between 1 and connUnitZoningAliasNumMembers." ::= { connUnitZoningAliasEntry 2 } connUnitZoningAliasNumAliases OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "The number of aliases defined in this table." ::= { connUnitZoningAliasEntry 3 } connUnitZoningAliasName OBJECT-TYPE SYNTAX DisplayString (SIZE (0..79)) ACCESS read-only STATUS mandatory DESCRIPTION "The alias name." ::= { connUnitZoningAliasEntry 4 } connUnitZoningAliasNumMembers OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "Number of members in the alias: connUnitZoningAliasName." ::= { connUnitZoningAliasEntry 5 } connUnitZoningAliasMemberIdType OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "Type of alias member ID: 1- Port WWN 2- Domain & Port ID 3- FC Address Others: reserved." ::= { connUnitZoningAliasEntry 6 } connUnitZoningAliasMemberID OBJECT-TYPE SYNTAX FcGlobalId ACCESS read-only STATUS mandatory DESCRIPTION "ID of the alias member based on connUnitZoningAliasMemberIdType." ::= { connUnitZoningAliasEntry 7 } ------------------------------------------------------------------ -- The following four tables have been obsoleted. These were used to -- keep statistic information based on the type of port type. It was -- changed for all ports to use a common statistics table. -- connUnitPortStatHubTable OBJECT-TYPE -- SYNTAX SEQUENCE OF ConnUnitPortStatHubEntry -- ACCESS not-accessible -- STATUS obsolete -- DESCRIPTION -- "A list of statistics for the hub port type." -- ::= { statSet 1 } -- connUnitPortStatFabricTable OBJECT-TYPE -- SYNTAX SEQUENCE OF ConnUnitPortStatFabricEntry -- ACCESS not-accessible -- STATUS obsolete -- DESCRIPTION -- "A list of statistics for the fabric port types." -- ::= { statSet 2 } -- connUnitPortStatSCSITable OBJECT-TYPE -- SYNTAX SEQUENCE OF ConnUnitPortStatSCSIEntry -- ACCESS not-accessible -- STATUS obsolete -- DESCRIPTION -- "A list of statistics for the SCSI port type." -- ::= { statSet 3 } -- connUnitPortStatLANTable OBJECT-TYPE -- SYNTAX SEQUENCE OF ConnUnitPortStatLANEntry -- ACCESS not-accessible -- STATUS obsolete -- DESCRIPTION -- "A list of statistics for the LAN/WAN port type." -- ::= { statSet 4 } -- There is one and only one statistics table for each -- individual port. For all objects in statistics table, if the object is not -- supported by the conn unit then the high order bit is set to 1 with all other -- bits set to zero. The high order bit is reserved to indicate if the object -- if supported or not. All objects start at a value of zero at hardware -- initialization and continue incrementing till end of 63 bits and then -- wrap to zero. -- Port Statistics connUnitPortStatTable OBJECT-TYPE SYNTAX SEQUENCE OF ConnUnitPortStatEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "A list of statistics for the fabric port types." ::= { statSet 5 } connUnitPortStatEntry OBJECT-TYPE SYNTAX ConnUnitPortStatEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "An entry describing port statistics." INDEX { connUnitPortStatUnitId, connUnitPortStatIndex } ::= { connUnitPortStatTable 1 } ConnUnitPortStatEntry ::= SEQUENCE { connUnitPortStatUnitId FcGlobalId, connUnitPortStatIndex INTEGER, connUnitPortStatCountError OCTET STRING, connUnitPortStatCountTxObjects OCTET STRING, connUnitPortStatCountRxObjects OCTET STRING, connUnitPortStatCountTxElements OCTET STRING, connUnitPortStatCountRxElements OCTET STRING, connUnitPortStatCountBBCreditZero OCTET STRING, connUnitPortStatCountInputBuffersFull OCTET STRING, connUnitPortStatCountFBSYFrames OCTET STRING, connUnitPortStatCountPBSYFrames OCTET STRING, connUnitPortStatCountFRJTFrames OCTET STRING, connUnitPortStatCountPRJTFrames OCTET STRING, connUnitPortStatCountClass1RxFrames OCTET STRING, connUnitPortStatCountClass1TxFrames OCTET STRING, connUnitPortStatCountClass1FBSYFrames OCTET STRING, connUnitPortStatCountClass1PBSYFrames OCTET STRING, connUnitPortStatCountClass1FRJTFrames OCTET STRING, connUnitPortStatCountClass1PRJTFrames OCTET STRING, connUnitPortStatCountClass2RxFrames OCTET STRING, connUnitPortStatCountClass2TxFrames OCTET STRING, connUnitPortStatCountClass2FBSYFrames OCTET STRING, connUnitPortStatCountClass2PBSYFrames OCTET STRING, connUnitPortStatCountClass2FRJTFrames OCTET STRING, connUnitPortStatCountClass2PRJTFrames OCTET STRING, connUnitPortStatCountClass3RxFrames OCTET STRING, connUnitPortStatCountClass3TxFrames OCTET STRING, connUnitPortStatCountClass3Discards OCTET STRING, connUnitPortStatCountRxMulticastObjects OCTET STRING, connUnitPortStatCountTxMulticastObjects OCTET STRING, connUnitPortStatCountRxBroadcastObjects OCTET STRING, connUnitPortStatCountTxBroadcastObjects OCTET STRING, connUnitPortStatCountRxLinkResets OCTET STRING, connUnitPortStatCountTxLinkResets OCTET STRING, connUnitPortStatCountNumberLinkResets OCTET STRING, connUnitPortStatCountRxOfflineSequences OCTET STRING, connUnitPortStatCountTxOfflineSequences OCTET STRING, connUnitPortStatCountNumberOfflineSequences OCTET STRING, connUnitPortStatCountLinkFailures OCTET STRING, connUnitPortStatCountInvalidCRC OCTET STRING, connUnitPortStatCountInvalidTxWords OCTET STRING, connUnitPortStatCountPrimitiveSequenceProtocolErrors OCTET STRING, connUnitPortStatCountLossofSignal OCTET STRING, connUnitPortStatCountLossofSynchronization OCTET STRING, connUnitPortStatCountInvalidOrderedSets OCTET STRING, connUnitPortStatCountFramesTooLong OCTET STRING, connUnitPortStatCountFramesTruncated OCTET STRING, connUnitPortStatCountAddressErrors OCTET STRING, connUnitPortStatCountDelimiterErrors OCTET STRING, connUnitPortStatCountEncodingDisparityErrors OCTET STRING } connUnitPortStatUnitId OBJECT-TYPE SYNTAX FcGlobalId ACCESS read-only STATUS mandatory DESCRIPTION "The connUnitId of the connectivity unit that contains this port stat table." ::= { connUnitPortStatEntry 1 } connUnitPortStatIndex OBJECT-TYPE SYNTAX INTEGER (0..2147483647) ACCESS read-only STATUS mandatory DESCRIPTION "A unique value among all entries in this table having the same connUnitPortStatUnitId, between 1 and connUnitNumPort[connUnitPortStatUnitId]." ::= { connUnitPortStatEntry 2 } connUnitPortStatCountError OBJECT-TYPE SYNTAX OCTET STRING (SIZE (8)) ACCESS read-only STATUS mandatory DESCRIPTION "A count of the errors that have occured on this port." ::= { connUnitPortStatEntry 3 } connUnitPortStatCountTxObjects OBJECT-TYPE SYNTAX OCTET STRING (SIZE (8)) ACCESS read-only STATUS mandatory DESCRIPTION "The number of frames/packets/IOs/etc that have been transmitted by this port. Note: A Fibre Channel frame starts with SOF and ends with EOF. FC loop devices should not count frames passed through. This value represents the sum total for all other Tx objects." ::= { connUnitPortStatEntry 4 } connUnitPortStatCountRxObjects OBJECT-TYPE SYNTAX OCTET STRING (SIZE (8)) ACCESS read-only STATUS mandatory DESCRIPTION "The number of frames/packets/IOs/etc that have been received by this port. Note: A Fibre Channel frame starts with SOF and ends with EOF. FC loop devices should not count frames passed through. This value represents the sum total for all other Rx objects." ::= { connUnitPortStatEntry 5 } connUnitPortStatCountTxElements OBJECT-TYPE SYNTAX OCTET STRING (SIZE (8)) ACCESS read-only STATUS mandatory DESCRIPTION "The number of octets or bytes that have been transmitted by this port. One second periodic polling of the port. This value is saved and compared with the next polled value to compute net throughput. Note, for Fibre Channel, ordered sets are not included in the count." ::= { connUnitPortStatEntry 6 } connUnitPortStatCountRxElements OBJECT-TYPE SYNTAX OCTET STRING (SIZE (8)) ACCESS read-only STATUS mandatory DESCRIPTION "The number of octets or bytes that have been received. by this port. One second periodic polling of the port. This value is saved and compared with the next polled value to compute net throughput. Note, for Fibre Channel, ordered sets are not included in the count." ::= { connUnitPortStatEntry 7 } connUnitPortStatCountBBCreditZero OBJECT-TYPE SYNTAX OCTET STRING (SIZE (8)) ACCESS read-only STATUS mandatory DESCRIPTION "Count of transitions in/out of BBcredit zero state. The other side is not providing any credit. Note, this is a Fibre Channel stat only." ::= { connUnitPortStatEntry 8 } connUnitPortStatCountInputBuffersFull OBJECT-TYPE SYNTAX OCTET STRING (SIZE (8)) ACCESS read-only STATUS mandatory DESCRIPTION "Count of occurrences when all input buffers of a port were full and outbound buffer-to-buffer credit transitioned to zero. There is no credit to provide to other side. Note, this is a Fibre Channel stat only." ::= { connUnitPortStatEntry 9 } connUnitPortStatCountFBSYFrames OBJECT-TYPE SYNTAX OCTET STRING (SIZE (8)) ACCESS read-only STATUS mandatory DESCRIPTION "Count of times that FBSY was returned to this port as a result of a frame that could not be delivered to the other end of the link. This occurs if either the Fabric or the destination port is temporarily busy. Port can only occur on SOFc1 frames (the frames that establish a connection). Note, this is a Fibre Channel only stat. This is the sum of all classes. If you cannot keep the by class counters, then keep the sum counters." ::= { connUnitPortStatEntry 10 } connUnitPortStatCountPBSYFrames OBJECT-TYPE SYNTAX OCTET STRING (SIZE (8)) ACCESS read-only STATUS mandatory DESCRIPTION "Count of times that PBSY was returned to this port as a result of a frame that could not be delivered to the other end of the link. This occurs if the destination port is temporarily busy. PBSY can only occur on SOFc1 frames (the frames that establish a connection). Note, this is a Fibre Channel only stat.This is the sum of all classes. If you cannot keep the by class counters, then keep the sum counters." ::= { connUnitPortStatEntry 11 } connUnitPortStatCountFRJTFrames OBJECT-TYPE SYNTAX OCTET STRING (SIZE (8)) ACCESS read-only STATUS mandatory DESCRIPTION "Count of times that FRJT was returned to this port as a result of a Frame that was rejected by the fabric. Note, This is the total for all classes and is a Fibre Channel only stat." ::= { connUnitPortStatEntry 12 } connUnitPortStatCountPRJTFrames OBJECT-TYPE SYNTAX OCTET STRING (SIZE (8)) ACCESS read-only STATUS mandatory DESCRIPTION "Count of times that FRJT was returned to this port as a result of a Frame that was rejected at the destination N_Port. Note, This is the total for all classes and is a Fibre Channel only stat." ::= { connUnitPortStatEntry 13 } connUnitPortStatCountClass1RxFrames OBJECT-TYPE SYNTAX OCTET STRING (SIZE (8)) ACCESS read-only STATUS mandatory DESCRIPTION "Count of Class 1 Frames received at this port. Note, this is a Fibre Channel only stat." ::= { connUnitPortStatEntry 14 } connUnitPortStatCountClass1TxFrames OBJECT-TYPE SYNTAX OCTET STRING (SIZE (8)) ACCESS read-only STATUS mandatory DESCRIPTION "Count of Class 1 Frames transmitted out this port. Note, this is a Fibre Channel only stat." ::= { connUnitPortStatEntry 15 } connUnitPortStatCountClass1FBSYFrames OBJECT-TYPE SYNTAX OCTET STRING (SIZE (8)) ACCESS read-only STATUS mandatory DESCRIPTION "Count of times that FBSY was returned to this port as a result of a Class 1 Frame that could not be delivered to the other end of the link. This occurs if either the Fabric or the destination port is temporarily busy. FBSY can only occur on SOFc1 frames (the frames that establish a connection). Note, this is a Fibre Channel only stat." ::= { connUnitPortStatEntry 16 } connUnitPortStatCountClass1PBSYFrames OBJECT-TYPE SYNTAX OCTET STRING (SIZE (8)) ACCESS read-only STATUS mandatory DESCRIPTION "Count of times that PBSY was returned to this port as a result of a Class 1 Frame that could not be delivered to the other end of the link. This occurs if the destination N_Port is temporarily busy. PBSY can only occur on SOFc1 frames (the frames that establish a connection). Note, this is a Fibre Channel only stat." ::= { connUnitPortStatEntry 17 } connUnitPortStatCountClass1FRJTFrames OBJECT-TYPE SYNTAX OCTET STRING (SIZE (8)) ACCESS read-only STATUS mandatory DESCRIPTION "Count of times that FRJT was returned to this port as a result of a Class 1 Frame that was rejected by the fabric. Note, this is a Fibre Channel only stat." ::= { connUnitPortStatEntry 18 } connUnitPortStatCountClass1PRJTFrames OBJECT-TYPE SYNTAX OCTET STRING (SIZE (8)) ACCESS read-only STATUS mandatory DESCRIPTION "Count of times that FRJT was returned to this port as a result of a Class 1 Frame that was rejected at the destination N_Port. Note, this is a Fibre Channel only stat." ::= { connUnitPortStatEntry 19 } connUnitPortStatCountClass2RxFrames OBJECT-TYPE SYNTAX OCTET STRING (SIZE (8)) ACCESS read-only STATUS mandatory DESCRIPTION "Count of Class 2 Frames received at this port. Note, this is a Fibre Channel only stat." ::= { connUnitPortStatEntry 20 } connUnitPortStatCountClass2TxFrames OBJECT-TYPE SYNTAX OCTET STRING (SIZE (8)) ACCESS read-only STATUS mandatory DESCRIPTION "Count of Class 2 Frames transmitted out this port. Note, this is a Fibre Channel only stat." ::= { connUnitPortStatEntry 21 } connUnitPortStatCountClass2FBSYFrames OBJECT-TYPE SYNTAX OCTET STRING (SIZE (8)) ACCESS read-only STATUS mandatory DESCRIPTION "Count of times that FBSY was returned to this port as a result of a Class 2 Frame that could not be delivered to the other end of the link. This occurs if either the Fabric or the destination port is temporarily busy. FBSY can only occur on SOFc1 frames (the frames that establish a connection). Note, this is a Fibre Channel only stat." ::= { connUnitPortStatEntry 22 } connUnitPortStatCountClass2PBSYFrames OBJECT-TYPE SYNTAX OCTET STRING (SIZE (8)) ACCESS read-only STATUS mandatory DESCRIPTION "Count of times that PBSY was returned to this port as a result of a Class 2 Frame that could not be delivered to the other end of the link. This occurs if the destination N_Port is temporarily busy. PBSY can only occur on SOFc1 frames (the frames that establish a connection). Note, this is a Fibre Channel only stat." ::= { connUnitPortStatEntry 23 } connUnitPortStatCountClass2FRJTFrames OBJECT-TYPE SYNTAX OCTET STRING (SIZE (8)) ACCESS read-only STATUS mandatory DESCRIPTION "Count of times that FRJT was returned to this port as a result of a Class 2 Frame that was rejected by the fabric. Note, this is a Fibre Channel only stat." ::= { connUnitPortStatEntry 24 } connUnitPortStatCountClass2PRJTFrames OBJECT-TYPE SYNTAX OCTET STRING (SIZE (8)) ACCESS read-only STATUS mandatory DESCRIPTION "Count of times that FRJT was returned to this port as a result of a Class 2 Frame that was rejected at the destination N_Port. Note, this is a Fibre Channel only stat." ::= { connUnitPortStatEntry 25 } connUnitPortStatCountClass3RxFrames OBJECT-TYPE SYNTAX OCTET STRING (SIZE (8)) ACCESS read-only STATUS mandatory DESCRIPTION "Count of Class 3 Frames received at this port. Note, this is a Fibre Channel only stat." ::= { connUnitPortStatEntry 26 } connUnitPortStatCountClass3TxFrames OBJECT-TYPE SYNTAX OCTET STRING (SIZE (8)) ACCESS read-only STATUS mandatory DESCRIPTION "Count of Class 3 Frames transmitted out this port. Note, this is a Fibre Channel only stat." ::= { connUnitPortStatEntry 27 } connUnitPortStatCountClass3Discards OBJECT-TYPE SYNTAX OCTET STRING (SIZE (8)) ACCESS read-only STATUS mandatory DESCRIPTION "Count of Class 3 Frames that were discarded upon reception at this port. There is no FBSY or FRJT generated for Class 3 Frames. They are simply discarded if they cannot be delivered. Note, this is a Fibre Channel only stat." ::= { connUnitPortStatEntry 28 } connUnitPortStatCountRxMulticastObjects OBJECT-TYPE SYNTAX OCTET STRING (SIZE (8)) ACCESS read-only STATUS mandatory DESCRIPTION "Count of Multicast Frames or Packets received at this port." ::= { connUnitPortStatEntry 29 } connUnitPortStatCountTxMulticastObjects OBJECT-TYPE SYNTAX OCTET STRING (SIZE (8)) ACCESS read-only STATUS mandatory DESCRIPTION "Count of Multicast Frames or Packets transmitted out this port." ::= { connUnitPortStatEntry 30 } connUnitPortStatCountRxBroadcastObjects OBJECT-TYPE SYNTAX OCTET STRING (SIZE (8)) ACCESS read-only STATUS mandatory DESCRIPTION "Count of Broadcast Frames or Packets received at this port." ::= { connUnitPortStatEntry 31 } connUnitPortStatCountTxBroadcastObjects OBJECT-TYPE SYNTAX OCTET STRING (SIZE (8)) ACCESS read-only STATUS mandatory DESCRIPTION "Count of Broadcast Frames or Packets transmitted out this port. On a Fibre Channel loop, count only OPNr frames generated." ::= { connUnitPortStatEntry 32 } connUnitPortStatCountRxLinkResets OBJECT-TYPE SYNTAX OCTET STRING (SIZE (8)) ACCESS read-only STATUS mandatory DESCRIPTION "Count of Link resets. This is the number of LRs received. Note, this is a Fibre Channel only stat." ::= { connUnitPortStatEntry 33 } connUnitPortStatCountTxLinkResets OBJECT-TYPE SYNTAX OCTET STRING (SIZE (8)) ACCESS read-only STATUS mandatory DESCRIPTION "Count of Link resets. This is the number LRs transmitted. Note, this is a Fibre Channel only stat." ::= { connUnitPortStatEntry 34 } connUnitPortStatCountNumberLinkResets OBJECT-TYPE SYNTAX OCTET STRING (SIZE (8)) ACCESS read-only STATUS mandatory DESCRIPTION "Count of Link resets and LIPs detected at this port. The number times the reset link protocol is initiated. These are the count of the logical resets, a count of the number of primatives. Note, this is a Fibre Channel only stat." ::= { connUnitPortStatEntry 35 } connUnitPortStatCountRxOfflineSequences OBJECT-TYPE SYNTAX OCTET STRING (SIZE (8)) ACCESS read-only STATUS mandatory DESCRIPTION "Count of Offline Primitive OLS received at this port. Note, this is a Fibre Channel only stat." ::= { connUnitPortStatEntry 36 } connUnitPortStatCountTxOfflineSequences OBJECT-TYPE SYNTAX OCTET STRING (SIZE (8)) ACCESS read-only STATUS mandatory DESCRIPTION "Count of Offline Primitive OLS transmitted by this port. Note, this is a Fibre Channel only stat." ::= { connUnitPortStatEntry 37 } connUnitPortStatCountNumberOfflineSequences OBJECT-TYPE SYNTAX OCTET STRING (SIZE (8)) ACCESS read-only STATUS mandatory DESCRIPTION "Count of Offline Primitive sequence received at this port. Note, this is a Fibre Channel only stat." ::= { connUnitPortStatEntry 38 } connUnitPortStatCountLinkFailures OBJECT-TYPE SYNTAX OCTET STRING (SIZE (8)) ACCESS read-only STATUS mandatory DESCRIPTION "Count of link failures. This count is part of the Link Error Status Block (LESB). (FC-PH 29.8). Note, this is a Fibre Channel only stat." ::= { connUnitPortStatEntry 39 } connUnitPortStatCountInvalidCRC OBJECT-TYPE SYNTAX OCTET STRING (SIZE (8)) ACCESS read-only STATUS mandatory DESCRIPTION "Count of frames received with invalid CRC. This count is part of the Link Error Status Block (LESB). (FC-PH 29.8). Loop ports should not count CRC errors passing through when monitoring. Note, this is a Fibre Channel only stat." ::= { connUnitPortStatEntry 40 } connUnitPortStatCountInvalidTxWords OBJECT-TYPE SYNTAX OCTET STRING (SIZE (8)) ACCESS read-only STATUS mandatory DESCRIPTION "Count of invalid transmission words received at this port. This count is part of the Link Error Status Block (LESB). (FC-PH 29.8). Note, this is a Fibre Channel only stat." ::= { connUnitPortStatEntry 41 } connUnitPortStatCountPrimitiveSequenceProtocolErrors OBJECT-TYPE SYNTAX OCTET STRING (SIZE (8)) ACCESS read-only STATUS mandatory DESCRIPTION "Count of primitive sequence protocol errors detected at this port. This count is part of the Link Error Status Block (LESB). (FC-PH 29.8). Note, this is a Fibre Channel only stat." ::= { connUnitPortStatEntry 42 } connUnitPortStatCountLossofSignal OBJECT-TYPE SYNTAX OCTET STRING (SIZE (8)) ACCESS read-only STATUS mandatory DESCRIPTION "Count of instances of signal loss detected at port. This count is part of the Link Error Status Block (LESB). (FC-PH 29.8). Note, this is a Fibre Channel only stat." ::= { connUnitPortStatEntry 43 } connUnitPortStatCountLossofSynchronization OBJECT-TYPE SYNTAX OCTET STRING (SIZE (8)) ACCESS read-only STATUS mandatory DESCRIPTION "Count of instances of synchronization loss detected at port. This count is part of the Link Error Status Block (LESB). (FC-PH 29.8). Note, this is a Fibre Channel only stat." ::= { connUnitPortStatEntry 44 } connUnitPortStatCountInvalidOrderedSets OBJECT-TYPE SYNTAX OCTET STRING (SIZE (8)) ACCESS read-only STATUS mandatory DESCRIPTION "Count of invalid ordered sets received at port. This count is part of the Link Error Status Block (LESB). (FC-PH 29.8). Note, this is a Fibre Channel only stat." ::= { connUnitPortStatEntry 45 } connUnitPortStatCountFramesTooLong OBJECT-TYPE SYNTAX OCTET STRING (SIZE (8)) ACCESS read-only STATUS mandatory DESCRIPTION "Count of frames received at this port where the frame length was greater than what was agreed to in FLOGI/PLOGI. This could be caused by losing the end of frame delimiter. Note, this is a Fibre Channel only stat." ::= { connUnitPortStatEntry 46 } connUnitPortStatCountFramesTruncated OBJECT-TYPE SYNTAX OCTET STRING (SIZE (8)) ACCESS read-only STATUS mandatory DESCRIPTION "Count of frames received at this port where the frame length was less than the minimum indicated by the frame header - normally 24 bytes, but it could be more if the DFCTL field indicates an optional header should have been present. Note, this is a Fibre Channel only stat." ::= { connUnitPortStatEntry 47 } connUnitPortStatCountAddressErrors OBJECT-TYPE SYNTAX OCTET STRING (SIZE (8)) ACCESS read-only STATUS mandatory DESCRIPTION "Count of frames received with unknown addressing. e.x. unknown SID or DID. the SID or DID is not known to the routing algorithm. Note. this is a Fibre Channel only stat." ::= { connUnitPortStatEntry 48 } connUnitPortStatCountDelimiterErrors OBJECT-TYPE SYNTAX OCTET STRING (SIZE (8)) ACCESS read-only STATUS mandatory DESCRIPTION "Count of invalid frame delimiters received at this port. An example is a frame with a class 2 start and and a class 3 at the end. Note, this is a Fibre Channel only stat." ::= { connUnitPortStatEntry 49 } connUnitPortStatCountEncodingDisparityErrors OBJECT-TYPE SYNTAX OCTET STRING (SIZE (8)) ACCESS read-only STATUS mandatory DESCRIPTION "Count of disparity errors received at this port. Note, this is a Fibre Channel only stat." ::= { connUnitPortStatEntry 50 } ------------------------------------------------------------------ -- -- the Fibre Channel Simple Name Server table -- -- The Fibre Channel Simple Name Server table contains an entry for each device -- presently known to this connUnit. There will not be any version on this since -- FC-GS3 does not define a version today. -- -- This table is accessed either directly if the management -- software has an index value or via GetNexts. The value of -- the indexes are not required to be contiguous. -- The total number of entries are defined by the size of the table connUnitSnsMaxEntry OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "The current number of entries in the table." ::= { connUnitServiceScalars 1 } connUnitSnsTable OBJECT-TYPE SYNTAX SEQUENCE OF ConnUnitSnsEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "This table contains an entry for each object registered with this port in the switch." ::= { connUnitServiceTables 1 } connUnitSnsEntry OBJECT-TYPE SYNTAX ConnUnitSnsEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "The Simple Name Server table for the port represented by ConnUnitSnsPortIndex ." INDEX { connUnitSnsId, connUnitSnsPortName, connUnitSnsPortIdentifier } ::= { connUnitSnsTable 1 } ConnUnitSnsEntry ::= SEQUENCE { connUnitSnsId OCTET STRING, connUnitSnsPortIndex INTEGER, connUnitSnsPortIdentifier FcAddressId, connUnitSnsPortName FcNameId, connUnitSnsNodeName FcNameId, connUnitSnsClassOfSvc OCTET STRING, connUnitSnsNodeIPAddress OCTET STRING, connUnitSnsProcAssoc OCTET STRING, connUnitSnsFC4Type OCTET STRING, connUnitSnsPortType OCTET STRING, connUnitSnsPortIPAddress OCTET STRING, connUnitSnsFabricPortName FcNameId, connUnitSnsHardAddress FcGlobalId, connUnitSnsSymbolicPortName DisplayString, connUnitSnsSymbolicNodeName DisplayString } connUnitSnsId OBJECT-TYPE SYNTAX OCTET STRING (SIZE (16)) ACCESS read-only STATUS mandatory DESCRIPTION "The connUnitId of the connectivity unit that contains this Name Server table." ::= { connUnitSnsEntry 1 } connUnitSnsPortIndex OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "The physical port number of this SNS table entry. Each physical port has an SNS table with 1-n entries indexed by ConnUnitSnsPortIdentifier (port address)" ::= { connUnitSnsEntry 2 } connUnitSnsPortIdentifier OBJECT-TYPE SYNTAX FcAddressId ACCESS read-only STATUS mandatory DESCRIPTION "The Fibre Channel ID for this entry in the SNS table." ::= { connUnitSnsEntry 3 } connUnitSnsPortName OBJECT-TYPE SYNTAX FcNameId ACCESS read-only STATUS mandatory DESCRIPTION "The Port WWN for this entry in the SNS table." ::= { connUnitSnsEntry 4 } connUnitSnsNodeName OBJECT-TYPE SYNTAX FcNameId ACCESS read-only STATUS mandatory DESCRIPTION "The Node Name for this entry in the SNS table." ::= { connUnitSnsEntry 5 } connUnitSnsClassOfSvc OBJECT-TYPE SYNTAX OCTET STRING (SIZE (1)) ACCESS read-only STATUS mandatory DESCRIPTION "The Classes of Service offered by this entry in the SNS table. This is a bit mask where each bit that represents the class of service is set to a value of one if the class is supported. Class 1 is bit zero." ::= { connUnitSnsEntry 6 } connUnitSnsNodeIPAddress OBJECT-TYPE SYNTAX OCTET STRING (SIZE(16)) ACCESS read-only STATUS mandatory DESCRIPTION "The IPv6 formatted address of the Node for this entry in the SNS table." ::= { connUnitSnsEntry 7 } connUnitSnsProcAssoc OBJECT-TYPE SYNTAX OCTET STRING (SIZE (8)) ACCESS read-only STATUS mandatory DESCRIPTION "The Process Associator for this entry in the SNS table." ::= { connUnitSnsEntry 8 } connUnitSnsFC4Type OBJECT-TYPE SYNTAX OCTET STRING (SIZE (32)) ACCESS read-only STATUS mandatory DESCRIPTION "The FC-4 Types supported by this entry in the SNS table." ::= { connUnitSnsEntry 9 } connUnitSnsPortType OBJECT-TYPE SYNTAX OCTET STRING (SIZE (1)) ACCESS read-only STATUS mandatory DESCRIPTION "The Port Type of this entry in the SNS table." ::= { connUnitSnsEntry 10 } connUnitSnsPortIPAddress OBJECT-TYPE SYNTAX OCTET STRING (SIZE(16)) ACCESS read-only STATUS mandatory DESCRIPTION "The IPv6 formatted address of this entry in the SNS table." ::= { connUnitSnsEntry 11 } connUnitSnsFabricPortName OBJECT-TYPE SYNTAX FcNameId ACCESS read-only STATUS mandatory DESCRIPTION "The Fabric Port name of this entry in the SNS table." ::= { connUnitSnsEntry 12 } connUnitSnsHardAddress OBJECT-TYPE SYNTAX FcGlobalId ACCESS read-only STATUS mandatory DESCRIPTION "The Hard ALPA of this entry in the SNS table." ::= { connUnitSnsEntry 13 } connUnitSnsSymbolicPortName OBJECT-TYPE SYNTAX DisplayString (SIZE (0..79)) ACCESS read-only STATUS mandatory DESCRIPTION "The Symbolic Port Name of this entry in the SNS table." ::= { connUnitSnsEntry 14 } connUnitSnsSymbolicNodeName OBJECT-TYPE SYNTAX DisplayString (SIZE (0..79)) ACCESS read-only STATUS mandatory DESCRIPTION "The Symbolic Node Name of this entry in the SNS table." ::= { connUnitSnsEntry 15 } -- Platform Table -- Design Objectives and Scope -- Simple, read-only view of platform registration entries. -- Platform registry is a service hosted by the connectivity unit, -- in a very similar manner as the SNS table. I.E., the platform -- table is contained by the connectivity unit. A platform can -- register it's attributes and platform nodes with the registry -- service. (See FC-GS-3 Configuration Server for details.) -- The platform table is a flat, double-indexed MIB table. -- To keep the table simple, only one platform management URL is exposed. -- If a platform registers more than one management URL, the first -- one is reported in this table. -- This table is based on the fabric configuration server -- defined in the FC-GS-3 standard and enhanced platform -- attributes proposed for FC-GS-4. -- Note that the information contained in this table may only -- contain the platforms that this connUnit can see or it may -- contain a fabric wide view of the platforms. connUnitPlatformMaxEntry OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "The maximum number of entries in the platform table." ::= { connUnitServiceScalars 2 } connUnitPlatformTable OBJECT-TYPE SYNTAX SEQUENCE OF ConnUnitPlatformEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "" ::= { connUnitServiceTables 2 } connUnitPlatformEntry OBJECT-TYPE SYNTAX ConnUnitPlatformEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "" INDEX { connUnitPlatformIndex, connUnitPlatformNodeIndex } ::= { connUnitPlatformTable 1 } ConnUnitPlatformEntry ::= SEQUENCE { connUnitPlatformIndex INTEGER, connUnitPlatformNodeIndex INTEGER, connUnitPlatformUnitID FcGlobalId, connUnitPlatformName OCTET STRING, connUnitPlatformType FcUnitType, connUnitPlatformLabel DisplayString, connUnitPlatformDescription DisplayString, connUnitPlatformLocation DisplayString, connUnitPlatformManagementUrl DisplayString, connUnitPlatformNumNodes INTEGER, connUnitPlatformNodeName FcGlobalId } connUnitPlatformIndex OBJECT-TYPE SYNTAX INTEGER (1..2147483647) ACCESS read-only STATUS mandatory DESCRIPTION "Unique table index for each platform. Valid values are between 1 and connUnitPlatformsMaxEntry." ::= { connUnitPlatformEntry 1 } connUnitPlatformNodeIndex OBJECT-TYPE SYNTAX INTEGER (1..2147483647) ACCESS read-only STATUS mandatory DESCRIPTION "Unique table index for each platform node. Valid values are between 1 and connUnitPlatformsNumNodes." ::= { connUnitPlatformEntry 2 } connUnitPlatformUnitID OBJECT-TYPE SYNTAX FcGlobalId ACCESS read-only STATUS mandatory DESCRIPTION "The connUnitId of the connectivity unit that contains this Platform table." ::= { connUnitPlatformEntry 3 } connUnitPlatformName OBJECT-TYPE SYNTAX OCTET STRING (SIZE(79)) ACCESS read-only STATUS mandatory DESCRIPTION "The platform name. May be either a readable string or a unique ID format as specified in the FC-GS-4 draft standard." ::= { connUnitPlatformEntry 4 } connUnitPlatformType OBJECT-TYPE SYNTAX FcUnitType ACCESS read-only STATUS mandatory DESCRIPTION "The platform type." ::= { connUnitPlatformEntry 6 } connUnitPlatformLabel OBJECT-TYPE SYNTAX DisplayString (SIZE (0..79)) ACCESS read-only STATUS mandatory DESCRIPTION "An administratively assigned symbolic name for the platform. The Platform Label shall only contain print-able ASCII characters." ::= { connUnitPlatformEntry 7 } connUnitPlatformDescription OBJECT-TYPE SYNTAX DisplayString (SIZE (0..79)) ACCESS read-only STATUS mandatory DESCRIPTION "A textual description of the platform. This value should include the full name and version identification of the platform's hardware type and software operating system. The Platform Description shall only contain printable ASCII characters." ::= { connUnitPlatformEntry 8 } connUnitPlatformLocation OBJECT-TYPE SYNTAX DisplayString (SIZE (0..79)) ACCESS read-only STATUS mandatory DESCRIPTION "The physical location of the platform (e.g., telephone closet, 3rd floor). The Platform Location shall only contain printable ASCII characters." ::= { connUnitPlatformEntry 9 } connUnitPlatformManagementUrl OBJECT-TYPE SYNTAX DisplayString (SIZE (0..79)) ACCESS read-only STATUS mandatory DESCRIPTION "Primary management URL for the platform. If the platform registers more than one URL, then this URL is equal to the first in the list." ::= { connUnitPlatformEntry 10 } connUnitPlatformNumNodes OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "Number of nodes contained in the platform." ::= { connUnitPlatformEntry 11 } connUnitPlatformNodeName OBJECT-TYPE SYNTAX FcGlobalId ACCESS read-only STATUS mandatory DESCRIPTION "The name (WWN - world wide name) of the node contained by the platform." ::= { connUnitPlatformEntry 12 } -- SNMP trap registration group trapMaxClients OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "The maximum number of SNMP trap recipients supported by the connectivity unit." ::= { trapReg 1 } trapClientCount OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "The current number of rows in the trap table." ::= { trapReg 2 } trapRegTable OBJECT-TYPE SYNTAX SEQUENCE OF TrapRegEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "A table containing a row for each IP address/port number that traps will be sent to." ::= { trapReg 3 } trapRegEntry OBJECT-TYPE SYNTAX TrapRegEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "Ip/Port pair for a specific client." INDEX { trapRegIpAddress, trapRegPort } ::= { trapRegTable 1 } TrapRegEntry ::= SEQUENCE { trapRegIpAddress IpAddress, trapRegPort INTEGER (1..2147483647), trapRegFilter FcEventSeverity, trapRegRowState INTEGER } trapRegIpAddress OBJECT-TYPE SYNTAX IpAddress ACCESS read-only STATUS mandatory DESCRIPTION "The Ip address of a client registered for traps." ::= { trapRegEntry 1 } trapRegPort OBJECT-TYPE SYNTAX INTEGER (1..2147483647) ACCESS read-only STATUS mandatory DESCRIPTION "The UDP port to send traps to for this host. Normally this would be the standard trap port (162). This object is an index and must be specified to create a row in this table." ::= { trapRegEntry 2 } trapRegFilter OBJECT-TYPE SYNTAX FcEventSeverity ACCESS read-write STATUS mandatory DESCRIPTION "This value defines the trap severity filter for this trap host. The connUnit will send traps to this host that have a severity level less than or equal to this value. The default value of this object is 'warning'." ::= { trapRegEntry 3} trapRegRowState OBJECT-TYPE SYNTAX INTEGER { rowDestroy(1), -- Remove row from table. rowInactive(2), -- Row exists, but TRAPs disabled rowActive(3) -- Row exists and is enabled for -- sending traps } ACCESS read-write STATUS mandatory DESCRIPTION "Specifies the state of the row. rowDestroy READ: Can never happen. WRITE: Remove this row from the table. rowInactive READ: Indicates that this row does exist, but that traps are not enabled to be sent to the target. WRITE: If the row does not exist, and the agent allows writes to the trap table, then a new row is created. The values of the optional columns will be set to default values. Traps are not enabled to be sent to the target. If the row already existed, then traps are disabled from being sent to the target. rowActive READ: Indicates that this row exists, and that traps are enabled to be sent to the target. WRITE: If the row does not exist, and the agent allows writes to the trap table, then a new row is created. The values of the optional columns will be set to default values. Traps are enabled to be sent to the target. If the row already exists, then traps are enabled to be sent to the target. A value of rowActive or rowInactive must be specified to create a row in the table." ::= { trapRegEntry 4} -- Related traps connUnitStatusChange TRAP-TYPE ENTERPRISE fcmgmt VARIABLES { connUnitStatus, connUnitState } DESCRIPTION "The overall status of the connectivity unit has changed. Recommended severity level (for filtering): alert" ::= 1 -- connUnitAddedTrap , 2, no longer used connUnitDeletedTrap TRAP-TYPE ENTERPRISE fcmgmt VARIABLES { connUnitId } DESCRIPTION "A connUnit has been deleted from this agent. Recommended severity level (for filtering): warning" ::= 3 connUnitEventTrap TRAP-TYPE ENTERPRISE fcmgmt VARIABLES { connUnitEventId, connUnitEventType, connUnitEventObject, connUnitEventDescr } DESCRIPTION "An event has been generated by the connectivity unit. Recommended severity level (for filtering): info" ::= 4 connUnitSensorStatusChange TRAP-TYPE ENTERPRISE fcmgmt VARIABLES { connUnitSensorStatus } DESCRIPTION "The overall status of the connectivity unit has changed. Recommended severity level (for filtering): alert" ::= 5 connUnitPortStatusChange TRAP-TYPE ENTERPRISE fcmgmt VARIABLES { connUnitPortStatus, connUnitPortState } DESCRIPTION "The overall status of the connectivity unit has changed. Recommended severity level (for filtering): alert" ::= 6 END