# Telegraf not send metrics in Influxdb and Grafana! **URL:** \ **Category:** Telegraf\ **Tags:** influxdb, telegraf, grafana\ **Created:** [September 8, 2021, 12:04pm UTC](https://community.influxdata.com/t/telegraf-not-send-metrics-in-influxdb-and-grafana/21610 "2021-09-08T12:04:03Z")\ **Posts on this page:** 1\ **Showing post:** 8
**Author:** ![Giovanni\_Luisotto](https://sea1.discourse-cdn.com/flex023/user_avatar/community.influxdata.com/giovanni_luisotto/32/4017_2.png) [@Giovanni\_Luisotto](https://community.influxdata.com/u/Giovanni_Luisotto)\ **Post date:** [September 15, 2021, 10:23am UTC](https://community.influxdata.com/t/telegraf-not-send-metrics-in-influxdb-and-grafana/21610/8 "2021-09-15T10:23:52Z")
Sorry but I don’t know much about the inputs.snmp and snmp, I doubt I can help you further. Your issue is a known one looks like, as I had a look around and found some related issues: > > > \### Relevant telegraf.conf: > \`\`\` > \# # Retrieves SNMP values from remote agents > … \[\[inputs.snmp\]\] > \# agents = \["127.0.0.1:161" \] > agents = \["ipdadrres\_switch:161"\] > \# ## Timeout for each SNMP query. > timeout = "5s" > \# ## Number of retries to attempt within timeout. > retries = 3 > \# ## SNMP version, values can be 1, 2, or 3 > version = 3 > \# > \# ## SNMP community string. > community = "public" > \# > \# ## The GETBULK max-repetitions parameter > max\_repetitions = 10 > \# > \# ## SNMPv3 auth parameters > sec\_name = "snmpuser" > auth\_protocol = "SHA" # Values: "MD5", "SHA", "" > auth\_password = "somethingsecret" > sec\_level = "authNoPriv" # Values: "noAuthNoPriv", "authNoPriv", "authPriv" > \## #context\_name = "" > priv\_protocol = "AES" # Values: "DES", "AES", "" > priv\_password = "somethingsecret" > > \[inputs.snmp.field\]\] > name = "hostname" > oid = "RFC1213-MIB::sysName.0" > is\_tag = true > > \[\[inputs.snmp.field\]\] > name = "uptime" > oid = "DISMAN-EXPRESSION-MIB::sysUpTimeInstance" > > # IF-MIB::ifTable contains counters on input and output traffic as well as errors and discards. > \[\[inputs.snmp.table\]\] > name = "interface" > inherit\_tags = \["hostname" \] > oid = "IF-MIB::ifTable" > > # Interface tag - used to identify interface in metrics database > \[\[inputs.snmp.table.field\]\] > name = "ifDescr" > oid = "IF-MIB::ifDescr" > is\_tag = true > > # IF-MIB::ifXTable contains newer High Capacity (HC) counters that do not overflow as fast for a few of the ifTable counters > \[\[inputs.snmp.table\]\] > name = "interface" > inherit\_tags = \["hostname" \] > oid = "IF-MIB::ifXTable" > > # Interface tag - used to identify interface in metrics database > \[\[inputs.snmp.table.field\]\] > name = "ifDescr" > oid = "IF-MIB::ifDescr" > is\_tag = true > > # EtherLike-MIB::dot3StatsTable contains detailed ethernet-level information about what kind of errors have been logged on an interface (such as FCS error, frame too long, etc) > \[\[inputs.snmp.table\]\] > name = "interface" > inherit\_tags = \["hostname" \] > oid = "EtherLike-MIB::dot3StatsTable" > > # Interface tag - used to identify interface in metrics database > \[\[inputs.snmp.table.field\]\] > name = "ifDescr" > oid = "IF-MIB::ifDescr" > is\_tag = true > \`\`\` > \### System info: > Telegraf : 1.8.1 > OS: Centos 7 > Activated plugins - vsphere, snmp, system > \### Steps to reproduce: > > 1. ... > 2. ... > > \### Expected behavior: > To be able to get SNMP metrics and pushed to Influx output > \### Actual behavior: > When running the telegraf test for config, fetches other metrics for System but no SNMP metrics > \`$telegraf --config /etc/telegraf/telegraf.conf --test\` > Also when checking the status > \`\`\` > $systemctl status telegraf.service -l > : Cannot find module (IPV6-UDP-MIB):At line 0 in (none) > : Cannot find module (IPV6-FORWARD-MIB):At line 0 in (none) > : Cannot find module (NET-SNMP-PASS-MIB):At line 0 in (none) > : Cannot find module (NET-SNMP-EXTEND-MIB):At line 0 in (none) > : Cannot find module (UCD-DLMOD-MIB):At line 0 in (none) > : Cannot find module (SNMP-NOTIFICATION-MIB):At line 0 in (none) > : Cannot find module (IF-MIB):At line 0 in (none) > : IF-MIB::ifTable:Unknown Object Identifier > \`\`\` > \### Additional info: > I also tried doing a snmpwalk, which works perfectly fine for the ip address. > \[Include gist of relevant config, logs, etc.\] > > > Hello, > i have installed Telegraf container v 1.5.3, but with this configuration… doesn't work: > > \`# Inet interface > \[\[inputs.snmp.table\]\] > oid = "IF-MIB::ifTable" > \[\[inputs.snmp.table.field\]\] > is\_tag = true > oid = "IF-MIB::ifDescr"\` > > is resulting in this error: > > \`! Error in plugin \[inputs.snmp\]: initializing table : translating: exit status 2: MIB search path: /root/.snmp/mibs:/usr/share/snmp/mibs:/usr/share/snmp/mibs/iana:/usr/share/snmp/mibs/ietf:/usr/share/mibs/site:/usr/share/snmp/mibs:/usr/share/mibs/iana:/usr/share/mibs/ietf:/usr/share/mibs/netsnmp > Cannot find module (IF-MIB): At line 0 in (none) > IF-MIB::ifTable: Unknown Object Identifier\` > > I have tried with 1.5 and 1.4, is the same thing. > > Regards > E. and another post in the community: > [@Cannot find module (IF-MIB)](https://community.influxdata.com/t/cannot-find-module-if-mib/4499/4): > > I created a custom docker build see below, which solve the problels. # Based on https://github.com/weldpua2008/docker-net-snmp FROM telegraf RUN export DEBIAN\_FRONTEND=noninteractive && \ export DEBIAN\_RELEASE=$(awk -F'["]' '/VERSION=/{print $3}' /etc/os-release | tr -cd '[[:alnum:]].\_-' ) && \ echo "remove main from /etc/apt/sources.list" && \ sed -i '/main/d' /etc/apt/sources.list && \ echo "remove contrib from /etc/apt/sources.list" && \ se… hope it helps --- _[View the full topic](https://community.influxdata.com/t/telegraf-not-send-metrics-in-influxdb-and-grafana/21610)._